1. Home
  2. Products
  3. Electric Conduits And Fittings
  4. PVC Insulating Electrical Pipes And Fittings (AS/NZS2053)
  5. PVC-U DEEP JUNCTION BOX 4 WAY
Categories
PVC-U DEEP JUNCTION BOX 4 WAY
PVC-U DEEP JUNCTION BOX 4 WAY
PVC-U DEEP JUNCTION BOX 4 WAY
PVC-U DEEP JUNCTION BOX 4 WAY
PVC-U DEEP JUNCTION BOX 4 WAY
PVC-U DEEP JUNCTION BOX 4 WAY
PVC-U DEEP JUNCTION BOX 4 WAY
PVC-U DEEP JUNCTION BOX 4 WAY
PVC-U DEEP JUNCTION BOX 4 WAY
PVC-U DEEP JUNCTION BOX 4 WAY
PVC-U DEEP JUNCTION BOX 4 WAY

PVC-U DEEP JUNCTION BOX 4 WAY

AED028
1. The inner and outer walls of the casing are smooth and the friction coefficient is small. It can reduce the resistance of wires and cables in the pipeline.
2. High compression resistance, it can be installed in the concrete in the open or concealed way, and will not be damaged under pressure. Medium and heavy pipe series are suitable for concealed laying in the concrete.
3. The casing has good impact resistance and heat resistance. During concrete pouring, the casing can withstand normal tamping impact without cracking, and will not soften and deform under the effect of concrete setting.
4. The casing has good moisture resistance, acid and alkali resistance, will not rust, and is acid, alkali and oil resistant. All joints shall be bonded with PVC adhesive according to the regulations, which can prevent water from seeping into the pipe and has better moisture-proof effect. Therefore, it is suitable for use in corrosive environment.
5. PVC has strong compression resistance, and can be installed in the concrete in an open or concealed manner, without being damaged by external pressure.
6. PVC electrical casing is light in weight, convenient in handling and construction, which can save a lot of labor and material resources.
PVC-U INSULATING ELECTRICAL PIPE AND FITTINGS
ERA PVC-U INSULATING ELECTRICAL PIPE AND FITTINGS, DEEP JUNCTION BOX 4 WAY, AED028,AS/NZS 2053,WATERMARK

Fusion Joints

HDPE piping systems can be joined with heat fusion welds. Heat fusion involves the heating of two HDPE surfaces then bringing them together to form a permanent, monolithic, leak-free system.

Unlike the fusion process developed for other plastics pipes, the fusion process for HDPE is proven and has been used by the natural gas industry for over 40 years. Approximately 95% of all gas distribution piping in  the United States is polyethylene pipe joined by heat fusion.

Fusing HDPE pipe is not difficult and personnel can be trained in the process.

Adaptability

In addition to joining HDPE with heat fusion, HDPE pipe can also be joined with Stab or Mechanical Fittings.

There are a wide range of these fittings available, specific to your pipe size and application.

Specification:
Model NumberAED028MaterialPVC-U
DescriptionPVC-U DEEP JUNCTION BOX 4 WAYSize20、25MM
StandardAS/NZS 2053ColorGrey
Working Pressure    /TemperatureMax 60°C / 140°F
ConnectionSocket & ThreadCertificateWATERMARK
 
 
Main Products:
The main characteristics of PVC pipe

1, very light quality, easy loading and unloading, low density, convenient construction.

2, good corrosion resistance, good acid resistance, alkali resistance, corrosion resistance, very suitable for chemical industry.

3, the fluid resistance is very small. The smooth roughness coefficient of the inner wall of the PVC pipe is only 0.009, and the fluid resistance is small, which greatly improves the hydraulic condition of the pipe network and reduces the operating cost of the system.

4. High mechanical strength, good pressure resistance, impact resistance and tensile strength.

5, the construction is simple, the pipeline connection construction is fast and simple, the construction cost is low.

6, the cost is cheap, the price is low, the transportation construction is convenient, the life is long, the overall cost is low.

7, the water quality does not affect the dissolution experiment proved, does not affect the water quality, suitable for large area of promotion and application.

8, the fluid resistance is very small, the PVC pipe wall is very smooth, the friction coefficient of the pipe wall is very small, can speed up the transmission time of the medium, so the transmission capacity is much better than the concrete of the same pipe diameter.

9, PVC material will not be bitten by rodents, and the service life will be much longer than the easy to bite material, so the use of PVC pipe in many areas can be guaranteed.

FAQ:
1.What is your MOQ?
 Our MOQ is usually 5 CTNS.
 
2.What is your delievery time?
 The time of delievery is around 30-45days.
 
3.What is the shipping port?
 We ship the goods via Ningbo or Shanghai port.
 
4.What is your payment terms?
 We accept 30% T/T in advance,70% in the period of shipment or 100% L/C.
 
5.How should I contact you?
 You can contact us with Trade Manager or send us an email by click Contact Supplier bottom.
 
6.What is the location of your company?
Our company is located in the Taizhou Zhejiang Province,China.
If you would like to have a visit, you are much welcome.
 
7.How about the samples?
We could send you the samples ,most samples are free to send to most places in China.If sent to other countries,transport fee shoule be paid by you.
 
8.Why choose us?
1 Genuine produces with excellent quality and competitive price.
2 Cooperating with the customers all over the world and knowing the markets very well.
3 ERA is a listed company. Everything can be rest assured working with us.
4 After- Services will be highly-satisfied. Any problems and feedbacks will be answered in a short of time.

Our Services:
1. Any inquiries will be replied within 24 hours
2. Professional manufacturer.
3. OEM is available.
4. High quality, standard designs, reasonable&competitive price, fast lead time.
5. Faster delivery: Sample will be prepared in 2-3days.
6. Shipping: We have strong cooperation with DHL, TNT, UPS, MSK, China Shipping, etc.